How to Trace a Floor Plan from a Photo or Image
An old blueprint, a listing floor plan or a hand sketch can become a real, measured plan. Here is how to scale the picture, trace over it, check it and export it as a PDF or a CAD file.
vPlan AR Team
vPlan AR
Plenty of floor plans only exist as pictures: a blueprint in a drawer, the plan from an old listing, a builder brochure, a sketch on squared paper. A picture can be printed but not edited, measured or sent to CAD. Tracing it turns it into a real plan, with walls at their true lengths, rooms with their areas, and a file an architect, contractor or permit office can use.
Tracing is done by hand: you put the picture under the drawing, set its scale and draw the walls over it. vPlan AR does not recognise walls in a picture by itself, but with the snaps and typed lengths a house takes far less time than drawing it from scratch. The steps below use the online floor plan maker, where Trace an image is on every plan, including Free.
What You Need
You need a picture file (JPG, PNG or another common image format) and one length you know for sure. The known length can be a dimension written on the drawing, such as a room marked 12' x 14', or a wall you measure in the house. The longer it is, the more accurate the scale: an outside wall is better than a closet.
A PDF of a plan needs to become an image first: open it and take a screenshot of the page, or save the page as a PNG from your PDF viewer. You also need a computer or tablet, since the web editor draws on a larger screen; on a phone it opens plans to view and mark up.
Get a Good Picture
A scanner gives the best result, because it keeps the drawing flat and square. With a phone, lay the plan flat in good light, hold the phone directly above it with the plan filling the frame, and keep the camera parallel to the paper. A picture taken at an angle stretches one side of the drawing, and no scale fixes that.
A listing image or brochure plan from a website can be used as it is, as long as it is the full plan and not cropped. Higher resolution makes corners easier to see when you zoom in.
Load the Picture and Set Its Scale
Start a new plan and choose Trace an image (also on the tool rail as Import image), then pick the file. The picture goes in the middle of the view, behind the canvas, and moves and zooms with the plan. A Trace image panel opens with its controls: Opacity, Move picture, Set scale, Hide, Replace and Remove.
Choose Set scale, click the two ends of the length you know, type its real length in your units and Apply. The picture is resized so that length is true, and everything else on it follows. Then fade it with the opacity slider so the walls you draw stand out, and use Move picture if you want it somewhere else on the canvas.
Trace the Walls
Pick the Wall tool (W) and click the corners of the outside walls on the picture, then the inside walls. Ortho (F8, or hold Shift) keeps walls straight, and object snaps make each wall meet the last one exactly, so the plan closes even where the picture is a little blurry. Walls can be drawn on either face, which helps when the drawing shows the outside line of the house.
Where the drawing has dimensions written on it, type them instead of clicking: point the cursor the way the wall runs, type the length and press Enter. A written dimension is more accurate than the picture, especially from a photo or a copy of a copy.
Doors, Windows and Rooms
Add doors (D), windows (N) and openings (O) by clicking the walls where the drawing shows them, and slide each one into place; the clear distance to each side shows as you move it. Rooms are found as the walls close, with their area and perimeter, so name them as the drawing does. If the drawing uses abbreviations such as W/D or WH, our floor plan symbols guide explains them.
Check It and Export
Hide the picture and look at the plan on its own, then check a few lengths with the Measure tool (Q) against the dimensions on the drawing or a tape in the house. Old drawings are not always what was built, so if you can, measure the rooms that matter. Fix a wrong wall by selecting it and typing its length.
The picture is kept in your browser only: it is never uploaded, and it is not saved with the plan, so trace a plan in one sitting or keep the file to pick again. The plan you drew saves to your account. Export it as a true-scale PDF on every plan (watermarked, one level, on Free), and on Pro as a multi-level plan set, a DXF for CAD or a 3D model. See our guide to drawing a floor plan to scale for printing at a real scale.
Frequently Asked Questions
Can I convert a floor plan image to CAD?
Yes, by tracing it: set the picture's scale from one known length, draw the walls over it and export the plan as a DXF, which opens in AutoCAD and other CAD programs. In vPlan AR, tracing is on every plan and DXF export is on Pro.
Can I trace a PDF floor plan?
Save the PDF page as an image first (a screenshot or a PNG export from your PDF viewer), then trace the image. If the PDF was drawn in CAD, ask whoever made it for the DXF or DWG instead.
How do I scale an image of a floor plan?
Find one length you know, ideally a long one such as an outside wall with a written dimension. Click its two ends on the picture, type the real length, and the whole picture is resized to match.
How accurate is a traced floor plan?
As accurate as the picture and the known length. A flat scan with a long known dimension traces closely; a photo taken at an angle or a small image does not. Check a few lengths against the house before relying on it.
Does vPlan AR upload the image I trace?
No. The picture stays in your browser while you trace and is not saved with the plan. Only the plan you draw is saved to your account.